Cool Modular House Building images

Some cool modular house building images:

Close up a solar heating panel in a modular house built near Corrales, New Mexico…, 04/1974
modular house building
Image by The U.S. National Archives
Original Caption: Close up a solar heating panel in a modular house built near Corrales, New Mexico. Closed at night, the panel is dropped during the day to allow sunlight to pass through the glass and heat blackened 55-gallon drums filled with water, 04/1974

U.S. National Archives’ Local Identifier: 412-DA-12856

Photographer: Norton, Boyd

Environmental protection
Natural resources
Albuquerque (New Mexico, United States) inhabited place

Persistent URL:

Repository: Still Picture Records Section, Special Media Archives Services Division (NWCS-S), National Archives at College Park, 8601 Adelphi Road, College Park, MD, 20740-6001.

For information about ordering reproductions of photographs held by the Still Picture Unit, visit:

Reproductions may be ordered via an independent vendor. NARA maintains a list of vendors at

Access Restrictions: Unrestricted
Use Restrictions: Unrestricted

Steel-Frame Modular House
modular house building
Image by

Steel-Frame Modular House
modular house building
Image by

Cool Cheap Building Supplies images

Some cool cheap building supplies images:

Steven F. Udvar-Hazy Center: main hall panorama
cheap building supplies
Image by Chris Devers

See more photos of this, and the Wikipedia article.

Details, quoting from Smithsonian National Air and Space Museum | _details_pending_:

My Make-up for the July 3rd “Red, White and Dead” Zombie Walk/Thriller Dance in Fremont
cheap building supplies
Image by CalamityJon
Okay, let’s take a moment to talk about the makeup. When I hit the theatrical supply store – and by the way, how odd is it that Redmond, Washington, of all places has a theatrical supply store? We only have, like, two bookstores and ZE-RO men’s clothiers. Everything else is either British pantries and Teriyaki places – I knew that I could walk out of there with pre-fabricated latex appliances and "Realistic Gory Wounds" and other assorted festering gashes or bloody abscesses easily applied with some brand of Spirit Gum marketed under the brand name "Makeup Glue".*

(*Which, by the way, is not to insinuate that our theatrical supply store is lacking in any particular way – it’s actually quite good, and the staff is both comfortingly knowledgeable about makeup techniques and pleasantly inviting of new knowledge. They have a pretty good supply in stock, although I felt strongly their lack of liquid latex. I had intended to render the wide, wondrous palette of my denuded pate as a series of mountainous, bloody crevasses and humourous valleys, but rather was relegated to the above muckings-about)

However, there is a part of me which refuses to buy anything wholesale – even if it’s cheaper and easier – if there’s a possibility of manufacturing it one’s-self from household goods and a little classic proletarian craftiness. This is the part of me that’s building a Flea Circus and a Coconut ventriloquist’s dummy, if you must know. I call it "The Plastic Hassle Part of Me."

SO, ceasing my beating around assorted bushes, here’s how my multitude of cranial and facial wounds were invented: Tracing paper, Elmer’s Glue and grease paint. You crumple the tracing paper (tissue paper would work infinitely better, but I’d bought and cannibalized an ENORMOUS sheet of the stuff for another craft project of the "Plastic Hassle" variety earlier, and was eager to make some additional use of my mutilated investment), then give it a good but brief soaking, effectively moistening the torn strips of paper without soaking them to the point of dissolution.

Once moistened, work a liberal (by which I mean, in the spirit of the day, "European Socialist Model") amount of Elmer’s white glue onto both sides of the paper. The water will thin it out and help it coat the paper equally on both sides, inasmuch as Elmer’s is water-soluble. Step whatever: Slap that shit on yo’ head. For extra depth of wounds, allow the first layer to dry and then slap additionally another layer or two on the existing layer. Make sure to let them dry between slappings.

I realize, at this point, you will resemble the victim of some sort of sheet-based bukkake, but that’s because the color needs be added. Using any sort of flat applicator, you’ll want to apply a coat of clown white to the dried, crinkled tracing paper, and following that and using a brush of some sort, you’ll add red, black and brown greasepaints to the textured areas of yo’ haid. I wish I could give you better advice about HOW to apply the colors, but a lot of it, for my part, was instinctive – I’ve spent about twenty-eight years of my life learning how to paint and how to color, so most of my knowledge is more reflex than it is intellectual. I will tell you that I went:

RED – for the thickest portions of the texturing
BLACK – for the areas surrounding the red
BROWN – for the areas leading into flesh.

From that point, there’s a lot of mopping, repainting, re-applying, and mopping again. After that, a quick dose of baby powder (Ideally, made from real babies) and another coat of Elmer’s over pretty much the majority of the face and head (the drying Elmer’s will both protect the existing paint and such, and also will dry in such a way on exposed skin as to make it wrinkle and crease).

Yeesh. After all of that, I haven’t yet talked about the actual Thriller Dance and Zombie Night! Good gravy! I think I’ll leave that for my Livejournal – in the meantime, please note that this photo represents me about twenty pounds lighter than I was in February, following four months of strict diet and exercise, and yet I still bet that no sweet young ladies will find themselves swooning over this photo, as much as large, hairy bears of the West Coast will. That’s okay. I find Bears to be comforting sorts of fellows, and after all, I have my one sweet young thing to swoon over me, if’n I need as much as that. Swoon away, Bears.

Okay, to my Livejournal, where I’ll finish this Great American Goddamn Novel of Greasepaint and Four-Counts …

Cool Builders images

Some cool builders images:

Stuckey’s Bridge Builder Plaque
Image by cmh2315fl
Bridge builders plaque for the historic Stuckeys Bridge over the Chunky River in Lauderdale County, Mississippi.

The bridge was built by the Virginia Bridge and Iron Company in 1901.

Fairground Street Bridge Builders Plaque
Image by cmh2315fl
Bridge builders plaque for the historic Fairground Street truss bridge over the Illinois Central Railroad yard in Vicksburg. The bridge was built by the Keystone Bridge Company in 1895.

Image by rafeejewell
Monday night was for exploring as we set off late that evening. Xavier took me to a wonderful place called the Bedrock – Flintstones Toon in Drymonia.

I simply adored this wonderful sim. The builders laid a loving hand throughout inspired by the well-known cartoon, the Flintstones.

I love sims that are created by builders who just build what they want without a corporate slant… Flintstones Town is a wild mix of fantasy trees, bedrock buildings, a cool dance floor and the fun bowling alley. Silly and sooo much fun.

We stayed there the entire night just playing and acting silly. We even changed our shape and skin into a butterfly and cartoony unicorn. Just a delightful place! So precious…

Cool Land And House images

Check out these land and house images:

Aeroplane which landed on a house through engine trouble
land and house
Image by National Library of Scotland
Aeroplane on a roof, Western Front, during World War I. This photograph of an aeroplane which has crash-landed on the roof of a building is a dramatic illustration of the flimsy nature of the early fighter planes. There is remarkably little apparent damage to the roof but the wood and fabric framework of the plane’s tail has folded up around a chimneystack.

Even as late as the spring of 1917, the Royal Flying Corps were losing about 50 planes every week. When possible, as appears to be happening in this case, the wreckage was salvaged and re-used.

[Original reads: ‘An aeroplane which landed on a house through engine trouble.’]

organic ecovillage drawing
land and house
Image by arimoore
a sketch of an idea. how do you start and then build an ecovillage for very little cost to the participants? my idea here was to collectively buy a farmhouse and barn, used temporarily for group housing while everyone builds together one, then another, then a whole group of resident-designed houses. (the ones here are all earth-bermed, passive solar designs. ithaca is COLD.) the houses would be built using timber, earth, stone, and other materials found on the land, with as little as possible going toward materials. windows and hardware would be found using freegan means. the houses would be off-grid.

the house/barn area would then go from group housing to a collective workshop / studio / guest room / office space, online and ongrid so folks can run cottage industries and have the room to do things collectively.

we’re actually interested in doing something along these lines (though collectively designed of course!), preferably with vegans but potentially with omnis, so long as collective funds and lands aren’t used for animal exploitation. here’s our listing in the intentional communities directory, for anyone interested in such things:…

Pierpoint Landing Light House
land and house
Image by Renee Silverman
Dec 2008 Flickr meet @ Long Beach – Pierpoint Landing & the Pike

Lighthouse jetting up @ Pierpoint Landing.

Cool Cheap Building Supplies images

A few nice cheap building supplies images I found:

Using vinegar for a natural clean
cheap building supplies
Image by elycefeliz
Circumvent the armada of commercial cleaners by keeping an ample supply of these eight items, which make up the basic ingredients for nearly every do-it-yourself cleaning recipe.
Distilled white vinegar: disinfects and breaks up dirt; choose white vinegar over apple cider or red vinegars, as these might stain surfaces
Baking soda: provides grit for scrubbing and reacts with water, vinegar or lemon by fizzing, which speeds up cleaning times
Borax: disinfects, bleaches and deodorizes; very handy in laundry mixes
Hydrogen Peroxide: disinfects and bleaches
Lemons: cut grease; bottled lemon juice also works well, although you might need to use bit more to get the same results
Olive oil: picks up dirt and polishes wood; cheaper grades work well
Vegetable based (liquid castile) soap: non-petroleum all-purpose cleaners
Washing soda: stain remover, general cleaner, helps unblock pipes; should be handled with gloves due to its caustic nature. Washing soda is usually found in the laundry aisle of grocery and drug stores.
Vinegar, baking soda, and lemons all have natural cleaning powers that rival manufactured cleaning solutions. They are easy and safe to use, and can often clean for much less money than other cleaning products on the market.…
How to clean your house without hurting the planet…
Vinegar, from the French translation meaning "sour wine," can be produced from all kinds of fruits, berries, melons, coconut, honey, beer, maple syrup, potatoes, beets, malt, grains and whey. But the fundamental process remains unchanged no matter what the initial ingredients may be: first a fermentation of sugar to alcohol, and then a second go-round to vinegar.

The ancients stumbled upon the versatility of vinegar probably 10,000 years ago. The Babylonians used it as medicine, and also mixed it with herbs to flavor their meals. The Romans drank it as a beverage. Biblical references show how it was used for its soothing and healing properties, and as recent as World War I vinegar was still being used to treat wounds.

Vinegar is a highly affordable and super-safe eco-cleaning staple we should all get familiar with. Distilled white vinegar easily neutralizes alkaline soaps, effortlessly breaks down stubborn urine odors, quickly polishes patent leather, instantly removes static cling from clothing, flawlessly cleans mirrors and glass, simply deodorizes the air, effortlessly polishes chrome, carefully removes soap scum and hard water spots, dependably cleans your automatic drip coffee maker and, in a pinch, even lifts accidentally spilled white glue. This 10,000 year-old elixir is a modern-day cleaning miracle!

Nixie clock – “Before” pictures – interior
cheap building supplies
Image by
This was the original "guts" of the military surplus digital indicator. It was full of early, military-spec TTL logic chips, with 1973 date codes. The digital logic board in the center is wire-wrapped, suggesting these devices were likely hand-assembled. This stuff didn’t come cheap in the early ’70s; original list price was 0. If you look carefully you can see that I’ve actually got two of them stacked up; I haven’t decided what to do with the second unit, yet.

It’s worth noting that there was enough TTL logic here to build a clock, given a 1 Hz input, some method to set it, and a few more gates to reset it to zero at 24:00:00. I wanted experience with PIC microcontrollers, though, and it really is more efficient to do this with a microprocessor instead of a dozen or so counter ICs.

Cool Cheap Building Supplies images

Some cool cheap building supplies images:

Steven F. Udvar-Hazy Center: Vought F4U-1D Corsair, with P-40 Warhawk in background
cheap building supplies
Image by Chris Devers
Quoting Smithsonian National Air and Space Museum | Vought F4U-1D Corsair :

By V-J Day, September 2, 1945, Corsair pilots had amassed an 11:1 kill ratio against enemy aircraft. The aircraft’s distinctive inverted gull-wing design allowed ground clearance for the huge, three-bladed Hamilton Standard Hydromatic propeller, which spanned more than 4 meters (13 feet). The Pratt and Whitney R-2800 radial engine and Hydromatic propeller was the largest and one of the most powerful engine-propeller combinations ever flown on a fighter aircraft.

Charles Lindbergh flew bombing missions in a Corsair with Marine Air Group 31 against Japanese strongholds in the Pacific in 1944. This airplane is painted in the colors and markings of the Corsair Sun Setter, a Marine close-support fighter assigned to the USS Essex in July 1944.

Transferred from the United States Navy.

Vought Aircraft Company


Country of Origin:
United States of America

Overall: 460 x 1020cm, 4037kg, 1250cm (15ft 1 1/8in. x 33ft 5 9/16in., 8900lb., 41ft 1/8in.)

All metal with fabric-covered wings behind the main spar.

Physical Description:
R-2800 radial air-cooled engine with 1,850 horsepower, turned a three-blade Hamilton Standard Hydromatic propeller with solid aluminum blades spanning 13 feet 1 inch; wing bent gull-shaped on both sides of the fuselage.

• • • • •

Quoting Smithsonian National Air and Space Museum | Curtiss P-40E Warhawk (Kittyhawk IA):

Whether known as the Warhawk, Tomahawk, or Kittyhawk, the Curtiss P-40 proved to be a successful, versatile fighter during the first half of World War II. The shark-mouthed Tomahawks that Gen. Claire Chennault’s "Flying Tigers" flew in China against the Japanese remain among the most popular airplanes of the war. P-40E pilot Lt. Boyd D. Wagner became the first American ace of World War II when he shot down six Japanese aircraft in the Philippines in mid-December 1941.

Curtiss-Wright built this airplane as Model 87-A3 and delivered it to Canada as a Kittyhawk I in 1941. It served until 1946 in No. 111 Squadron, Royal Canadian Air Force. U.S. Air Force personnel at Andrews Air Force Base restored it in 1975 to represent an aircraft of the 75th Fighter Squadron, 23rd Fighter Group, 14th Air Force.

Donated by the Exchange Club in Memory of Kellis Forbes.

Curtiss Aircraft Company


Country of Origin:
United States of America

Overall: 330 x 970cm, 2686kg, 1140cm (10ft 9 15/16in. x 31ft 9 7/8in., 5921.6lb., 37ft 4 13/16in.)

All-metal, semi-monocoque

Physical Description:
Single engine, single seat, fighter aircraft.

2011 Mac Mini Server Disassembly / Raid-0 SSD Upgrade
cheap building supplies
Image by Schill
(This is a summary from my Mac Mini SSD RAID-0 Project, see the set for more photos and a video.)

[ General disclaimer: These are my findings posted for the curious, you do all of this at your own risk, don’t blame me if stuff breaks etc. ]

Holy crap, I don’t want to ever have to do that again. Hopefully, it still works when reassembled with 8 GB of RAM and dual SSDs. In theory, it just might work. (Update: I now feel comfortable with this after tearing down and rebuilding a few times – and two weeks’ of running time later, no problems.)

Yes, this whole operation is somewhat frivolous. The stock dual 7200-RPM 500-GB 2.5" drives will themselves be configured as SPAN and in an external enclosure, driven via Firewire 800.

Not in the frame: Mainboard.

Tools used: Torx T6 and T8 screwdrivers (and, I think, a Philips #00) and a Dogfish Head 90-minute IPA.

I referenced a teardown guide from ifixit for the "steps" and post-it notes, so I could remember what went where when reassembling. (Note: not all steps apply, you don’t need to disconnect the bluetooth module etc.)

For the hard drive removal / upgrade process, this OWC video was handy and has rather hilarious background muzak. Note that there are different videos for server vs. non-server models.

General tips
Don’t bother with the crappy screwdriver "kits" (eg. the blue and green ones by the RAM in this photo) – go to your local hardware store (or online) and pay the or whatever it might cost per tool for quality Torx T6, T8, and (if needed) Philips #00 screwdrivers. One of the cheap ones, in one case, didn’t fit one fan screw I was trying to remove. However, the so-called plastic "spudger" tool did come in handy for pulling up cables and nudging other things where fingers wouldn’t reach, and where metal was not a good choice to use.

Removing the "mainboard"
The OWC video suggested you should put screwdrivers into holes on the mainboard, and pull back; this seems like a great way to break or snap the PCB and/or accidentally ruin traces along the way. I tried pulling several times, but it seemed that no amount of careful force would budge the thing.

Instead, I turned the mini around and carefully pushed the heat sink / vent outward using my thumbs, and with a little pressure, was able to pop the board out. The heatsink is just behind where the screw holes are shown in the video, toward the connector plate. It is pretty tight as the plate (where all the USB + power connectors etc. are) has snaps/clips on either end holding it in, but it does eventually give.

Once you get the mainboard, the rest is easy. Don’t pull the board fully out until any attached power cables etc. have been disconnected – and once the board is out, you can take out the power supply and HD chassis.

I also recommend booting the computer upside-down and with the bottom cover off once after reassembling, just to make sure the fan starts up; I noticed that mine didn’t at first(!), because the tiny fan power connector was not fully-seated on the mainboard when I put it back in. No fan would’ve meant a toasted CPU at some point, so make sure you check that. Use a flat plastic tool or something to push the connector flush with the board, to ensure it’s seated nicely.

Also, there’s a bit of a trick with the wireless module / antenna / grill assembly when popping it out and in – I think it slides underneath into place, so keep that in mind. Similar moves apply to the black plastic cowling at the bottom left near the fan. Sometimes things need a little jiggling to get into place.

Re-installing Lion: ⌘-R / Internet Recovery FTW
On mid-2011(?) Mac hardware, push and hold Apple-R (⌘-R) during boot to kickstart the Lion Recovery mode, with wifi or an ethernet cable connected. It’ll attempt to boot from a Lion recovery partition normally installed, and when that fails, it will magically go out on the Internets, and download and install and boot the recovery partition. That will run and after disk set-up and partitioning etc., another download of up to 7 GB (at least, according to my router’s traffic for that day) will happen, Lion will install, reboot, and voila.

Partitioning the SSDs, overprovisioning and stripe block size
From what I read online, it was recommended to leave up to 20% "unpartitioned" empty space for "overprovisioning" with an SSD to help with performance (garbage collection) and reliability. I got two OCZ Vertex III 60 GB SSDs, and using the disk utility built into the Lion installer, set them up with two partitions: [ 48 GB ext3 / 12 GB empty space ]. As for stripe block size, I had heard 64 KB or 128 KB as general recommendations, so I used 128.

Performance results
With SATA 3.0 (up to 6 gbps) and SandForce 2xxx controllers on the OCZ SSDs pushing up to 550 MB/sec read rates, I was able to get 1000+ MB/sec on larger files in benchmarks.

RAID-0 pros/cons: Worth it, or is one SSD enough?

– Wow, up to 1000 MB/sec. That is a shiny number.

– If one drive goes south, you lose everything.
– In most cases, 1000 MB/sec is a theoretical maximum you’ll hit only in benchmarks. Small bursts may be more realistic, and in most cases with less-compressible data, numbers will be much lower (albeit, 250+ MB/sec or whatever is still nothing to sneeze at.)

If you’re a tinkerer / overclocking fan and don’t fear the risk of data loss (i.e., you make time machine or image backups), RAID-0 is worth trying just for the fun of it. Otherwise, I think one SSD alone makes a huge difference in responsiveness given near-zero seek times etc., and with theoretical maximums of 500 MB/sec, that’s plenty of I/O for just about anybody.

BAC 1-11
cheap building supplies
Image by alex drennan
, also known as the BAC-111 or the BAC-1-11, was a British short-range jet airliner of the 1960s and 1970s. Conceived by Hunting Aircraft, it was developed and produced by the British Aircraft Corporation when Hunting merged into BAC along with other British aircraft makers in 1960.

The One-Eleven was designed to replace the Vickers Viscount on short-range routes. It was the second short-haul jet airliner to enter service, the first being the French Sud Aviation Caravelle. Due to its later service entry, the One-Eleven took advantage of more efficient engines and airline experience of jets. This made it popular, with over half of the sales at its launch being in the largest and most lucrative market, the United States. The One-Eleven was one of the most successful British airliner designs, and served until its widespread retirement in the 1990s due to noise restrictions
On 9 May 1961 British United Airways (BUA) placed the first order for ten One-Eleven 200s. On 23 October Braniff in the United States ordered six. Other orders followed from Mohawk for four, Kuwait Airways for three, and Central African Airways for two. Braniff subsequently doubled its order to twelve, while Aer Lingus ordered four. Western Airlines ordered ten aircraft but later cancelled. Bonanza Air Lines also wanted to order One-Elevens at a later stage but was stopped by a protectionist action of the US Department of Transportation
In May 1963, BAC announced the One-Eleven 300 and 400. The new versions used the Mk. 511 version of the Spey with increased power, allowing more fuel upload and hence longer range. There were a number of other changes, with the main visual difference being in the nosewheel doors. The difference between the 300 and 400 lay in their equipment and avionics, with the 400 intended for sales in the USA and thus equipped with US instruments. American Airlines ordered fifteen aircraft on 17 July 1963, bringing the order total to sixty, plus options for many more. American Airlines eventually bought a total of thirty of the 400-series, making that airline the largest ever customer of One-Elevens. This was assumed to be enough for BAC to break even on the project. In retrospect, however, many have doubted whether BAC and its successors made money on the One-Eleven.
The prototype (G-ASHG) rolled out of the Hurn assembly hall on 28 July 1963, its first flight following soon on 20 August.[1] This was almost a year ahead of the competing US airliner, the Douglas DC-9. This lead was commercially most important, since — as shown by the Bonanza case — US authorities could refuse to approve sales of foreign aircraft to domestic airlines where an American alternative existed.
The One-Eleven prototype, flown by test pilot Mike Lithgow, crashed with the loss of all on board on 22 October during stall testing. The investigation led to the discovery of what became known as deep stall or superstall, a phenomenon caused by reduced airflow to the tailplane caused by the combined blanking effects of the wing and the aft-mounted engine nacelles at high angles of attack, which prevents recovery of normal (nose-down) flight. To preclude such stalls, BAC designed and added devices known as stick shakers and stick pushers to the One-Eleven’s control system. It also redesigned the wing’s leading edge to smooth airflow into the engines and over the tailplane. The specially modified aircraft used for testing this problem is located at Brooklands Museum, Weybridge, Surrey, UK.
Despite the crash, testing continued and customer confidence remained high. American Airlines and Braniff took up their optional orders and placed further ones in February 1964. Further orders came from Mohawk, Philippine Airlines and Helmut Horten who ordered the first Executive modification of the aircraft. By the end of 1964, thirteen aircraft had rolled off the production line.
The One-Eleven was certified and the first handover, of G-ASJI to BUA, was on 22 January 1965. After several weeks of route-proving flights, the first revenue service flew on 9 April from Gatwick to Genoa. Braniff took delivery of their first aircraft on 11 March, while Mohawk received their first on 15 May. Deliveries continued, and by the end of 1965 airlines had received 34 aircraft. Demand continued to be buoyant, with a second production line set up at Weybridge.
In 1967 a larger 119-seat version was introduced as the One-Eleven 500 (also known as Super One-Eleven). This "stretched" version was delayed for at least a year while its launch customer BEA assessed its requirements. This gave competing US aircraft (the DC-9 and Boeing 737) the chance to make up for the One-Eleven’s early penetration of their domestic market. The British aircraft’s initial one-year advantage now turned into a one-year delay and the 500 failed to sell in the USA. Compared with earlier versions, the One-Eleven 500 was longer by 8 ft 4in (2.54 m) ahead of the wing and 5 ft 2in (1.57 m) behind it. The wing span was increased by 5 ft (1.5 m), and the latest Mk. 512 version of the Spey was used. The new version sold reasonably well across the world, particularly to European charter airlines. In 1971 it received an incremental upgrade to reduce drag and reduce runway requirements.
BEA/British Airways 500 series aircraft (denoted 1-11 510ED) varied significantly from other 1-11s, at BEA’s request. The One-Eleven 510ED had a modified cockpit which incorporated instrumentation and avionics from or similar to that of the Hawker Siddeley HS.121 Trident, for better commonality with the type (which at the time was the BEA/BA shorthaul workhorse). Their additional equipment included a more sophisticated autoflight system, which allowed CAT II autolandings and included an autothrottle (autoland functionality was removed from most aircraft later in their careers). The modifications went as far as reversing the "on" position of most switches to match that of the Trident; indeed, the 510ED was so different from other One-Elevens and 500 series aircraft that a different type rating was required to fly it, despite the fact that aside from the flight deck it was basically identical to all other 500 series aircraft.
Having faced competition "from above" with the aforementioned US aircraft by 1966, by 1970 the One-Eleven also faced competition "from below." The new competitor was the Fokker F28. Available as a four-member "family," it was lighter, less complex, and cheaper. The One-Eleven 475 of 1970 was launched to compete with the F.28. It combined the 400 fuselage with the higher power and larger wing of the 500 and was intended for hot and high operations. Only ten of the One-Eleven Mk 475 were sold. In 1977, the One-Eleven 670, a quiet and updated 475, was offered to the Japanese domestic market, failing to sell.
Total deliveries for 1966 stood at 46 aircraft, and another 120 were delivered by 1971. At this point orders slowed to a trickle. British production continued until 1982. There were two reasons why the production line was kept open for just 35 aircraft delivered over 11 years: first, BAC hoped that Rolls-Royce would develop a quieter and more powerful version of the Spey engine, making possible further One-Eleven developments; second, throughout the early part of the period Romania was negotiating to buy the entire One-Eleven programme and transfer production of the type to Bucharest.
By 1974, BAC invested significant effort into launching the One-Eleven 700. This had a longer body with a 134-seat interior and the projected Spey 67 engine producing greater power. It was approximately the same size as the latest DC-9s and 737s and would have been available in time to prevent large-scale defections by One-Eleven clients to McDonnell-Douglas and Boeing. Rolls-Royce was still recovering from bankruptcy, however, and the uprated Spey failed to materialise. An altogether less ambitious 700 made a reappearance in 1978 as a 500 with specially "hush-kitted" Speys which would be replaced by the proposed RB432 in the mid-1980s. This was offered to British Airways in competition with Boeing 737-200s, but was rejected.
In 1977, BAC merged with Hawker Siddeley to form British Aerospace (BAe) and the One-Eleven 800 was proposed with CFM-56 engines. It would have accommodated some 150 passengers in a mixed class layout. The One-Eleven 800’s fate was involved with the development of a European competitor to ubiquitous U.S. short/medium range airliners and it did not progress to the design stage.
The BAC Two-Eleven and BAC Three-Eleven were British airliner studies proposed by the British Aircraft Corporation in the late 1960s which never made it to production.
On 9 June 1979, Romanian president Nicolae Ceauşescu signed the contract for One-Eleven licence production in Romania.[3] This was to involve the delivery of three complete One-Elevens plus the construction of at least 22 in Bucharest, with reducing British content. It also involved Romanian production of Spey engines and certification of the aircraft to British and US standards. A market for up to 60 or even 80 cheap Romanian-built aircraft was mooted at the time, largely in China, the Third World and possibly Eastern Europe. The aircraft was redesignated ROMBAC 1-11.
The first Rombac One-Eleven, (YR-BRA cn 401) a series 561RC was rolled out at Romaero Băneasa factory on 27 August 1982, and flew for the first time on 18 September 1982. Production continued until 1989 at a much slower pace than foreseen in the contract: nine aircraft were delivered. The first aircraft was delivered to TAROM on 29 December 1982. The Romanian carrier took delivery of all but two of the aircraft produced, with the remaining two going to Romavia, the last of which (YR-BRI cn 409) was delivered on 1 January 1993.
There were three reasons why the Rombac initiative failed: Romania’s economy and international position deteriorated to the point where supplies for One-Eleven manufacture slowed to a trickle; the market foreseen by the Romanians failed to show an interest, though some Rombac machines were leased out to European operators; the One-Eleven’s noise level and fuel economy had failed to keep pace with US and West European competition. With reference to the last reason, Rolls-Royce repeatedly refused to allow its Tay engine to be used on Romanian One-Elevens.[citation needed] This reluctance is assumed[by whom?] to reflect fears that the Fokker 100, the Tay’s launch airframe, would suffer from Romanian competition
Total production of the One-Eleven in British and Romanian factories was 244, with two airframes left incomplete in Romania. A major initiative to re-engine corporate One-Elevens with Tay engines gathered pace in the USA in the late 1980s and early 1990s but came to nought after several successful test flights. Passive opposition from the engine maker among other factors is claimed to have sabotaged its chances of success.
One-Elevens served widely in the USA until displaced by the indigenous Douglas DC-9 and Boeing 737 in the early 1970s. In Europe they were common, continuing in widespread use until the mid-1980s and into the 1990s. Many One-Elevens then moved to smaller airlines, notably in the Far East and Africa. The last major operations were in Nigeria, where they were grounded after a crash in 2002. Today only a handful are still operating, mainly in Africa, though corporate versions survive in the USA and Europe. A further nail in the coffin for the One-Eleven in Europe was the Stage III noise abatement regulations which took effect from March 2003. The costs of bringing the Rolls-Royce Spey engines into compliance with this, by developing a hush kit, proved an expensive prospect for the smaller operators still using this aircraft type. Therefore very few 1-11s were fitted with hush kits, and most European operators disposed of the type from their fleet. Several dozen One-Elevens are in storage and for sale around the world.
British Airways retired its last One-Eleven in 1998.
In 2010, the EASA accepted an Airbus request to revoke the Type Certificate for the British Aerospace BAC One Eleven (BAC 1-11).[4] As a result, BAC 1-11 aircraft registered in any EU Member State will no longer be eligible for a Normal Certificate of Airworthiness

Cool Balconies images

A few nice balconies images I found:

Fallen Balcony
Image by Sentience
Moving into a brand new building isn’t turning out to be the the worry-free experience for which we had hoped. A neighbour’s balcony collapsed over the weekend, neatly crushing the air conditioner of their downstairs neighbour.

Being at courtyard level, we don’t have a balcony, and the one above us is connected to two walls, so we’re not sweating this as much as, say, the people across the courtyard who have a balcony identical to the one that fell.

Image by sez9
Balcony in old town chania